Laxmi Infrastructure

Epoxy resin concrete bonding agentUsesFor bonding fresh wet cementitious materials to existingcementitious surfaces. For use on horizontal surfaces or onvertical surfaces where mortar or concrete can be supportedby formwork. The long ‘open’ life makes it suitable for usewith formwork or where additional steel reinforcement has tobe fi tted. The product is ideal for roads, bridges, pavements,loading bays and factories, building segment and for bondedor granolithic fl oor toppings. Nitobond EP is equally suited tointernal and external applications.  USES- For bonding fresh wet cementitious materials to existing cementitious surfaces. For use on horizontal or vertical surfaces where mortar or concrete can be supported by formwork. The long ‘open’ life makes it suitable for use with formwork or where additional steel reinforcement has to be fitted. The product is ideal for roads, bridges, pavements, loading bays and factories, and for bonded or granolithic floor toppings. Nitobond EP is equally suited to internal and external applications. Nitobond EP may also be used as part of a repair system where a substrate/repair barrier is required or where the repair/ substrate is likely to become immersed, permanently wet or damp subsequent to the completion and cure of the repair.   Properties Compressive strength: 50 MPa        Tensile strength: 20 MPa, Flexural strength: 35 MPa Shear strength: 25 MPa Adhesive bond to concrete: In general, the bond will exceed the tensile strength of the host concrete VOC content: 19g / litre Pot life: 35 - 45 minutes @ 20°C Initial hardness: 24 hours @ 20°C Full cure: 7 days @ 20°C Max. overlay time: 90 minutes @ 20°C

High performance two componentelastomeric cementitious damp-proofcoating.UsesNitoproof Damp Protect is a High performance two componentelastomeric cementitious damp-proof coating, suitable for applicationon concrete, brick wall and plastered surface bothpositive & negative side.

Additional Information:

• Delivery Time: 9.00AM TO 6.00 PM

USES- Cebex 100 is an admixture for cementitious grouts wherea reduced water/cement ratio and positive expansions arerequired. Applications include bed grouting, duct grouting,non-shrink infi lling and jointing.                              Advantages Gaseous expansion system compensates for plasticshrinkage and settlement in properly designed cementitiousgrout. Reduced water/cement ratio mixes in the grout mix ensureslow permeability and long term durability in service. Gives grout high fl uidity with low water/cement ratio, thusmaking placement or injection of the grout easy. No metallic iron content to corrode and cause staining ordeterioration due to rust expansion in the grout. Composition allows high early strength development ingrouts, without the use of chlorides        DescriptionCebex 100, a plasticised expanding grout admixture is suppliedas a powder. The material is a combination of a plasticisingagent and a gas producing expansion medium. The plastisicingagent allows the use of a reduced water/cement ratio withconsequent increased strengths and durability. The expansivemedium counteracts the natural settlement and plastic shrinkageof the grout and aids stability and cohesion.

Additional Information:

• Delivery Time: 9.00AM TO 6.00 PM

High strength, abrasion resistant epoxy reinstatement mortar. Uses Nitomortar S is used for the fast and permanent reinstatement of concrete, particularly where high strength, abrasion resistance and chemical resistance are required. The product is designed for horizontal use but can be applied vertically, although generally in thinner sections. It is ideally suited for acid tanks, sea walls, industrial fl oors and for use as a bedding mortar. Nitomortar S can be used for emergency repairs where fast strength gain is important. When properly compacted, the mortar is highly impermeable. In certain instances, Nitomortar S can be used on metal substrates. Contact the local Fosroc offi ce for advice in this respect.

Additional Information:

• Delivery Time: 9.00Am To 6.00 Pm

Rapid setting cement based, water leakplugging mortar
For the rapid temporary patching and plugging of concretesegments, concrete and brick tunnel linings, sewage systems,below ground access chambers, pipes, basements, foundationsand mines.

Additional Information:

• Delivery Time: 9.00Am To 6.00 Pm
• Packaging Details: 15 Kg Packing

Product Details :
Uses
Sealing movement joints in building and civil engineering structures, including superstructures, floors, basements and subways.

Advantages

Meets key international standards

Forms a tough, elastic, rubber-like seal

Accommodates continuous and pronounced cyclic movement

Excellent adhesion to most common substrates, including primed concrete, glass, aluminium and stainless steel

High resistance to ageing reduces physical damage due to climatic extremes

Description
Thioflex 600 is available in gun and pouring grades. The gun grade is ideal for general application. It is packed in a ready to mix, 2.5 litre tin containing the base and curing agent in the correct proportions. The pouring grade for joints in horizontal surfaces is supplied in 5 litre packs with the base and curing agent in separate tins.

Thioflex 600 is particularly recommended for use in high-rise buildings and other applications where access for subsequent maintenance will be difficult and the risk of early movement failure must be minimised. It is also suitable for sealing joints in brickwork, retaining walls, basements and subways.

Thioflex 600 pouring grade is recommended for initial sealing of expansion joints and stress relief joints in floors and sealing other horizontal surfaces.

Design criteria

Thioflex 600 may be applied to joints between 5 and 50 mm wide. Joints which are expected to experience cyclicmovements should be designed to an optimum width : depth ratio of 2:1, subject to the overriding recommended minimum sealant depths set out below:

5 mm for metals, glass and other non-porous surfaces;
10 mm for all porous surfaces;
20 mm for trafficked joints and those subject to hydrostatic pressures.
To ensure that the sealant remains within its stated movement capacity (25% MAF), sealing slot widths should be designed in accordance with the recommendations of BS 6093. The use of a surface primer is always required on porous surfaces. On non-porous surfaces a primer is not normally required except where glass or glazed surfaces are to be permanently immersed in water.

Cementitious Tile Joint FillerUsesNitotile grout is a high quality polymer-modifi ed, water resistant,cement based grout designed for grouting glazed wall tiles, porcelaintiles, mosaic, vitrifi ed and fully vitrifi ed tiles, natural andengineered stones for both interior and exterior applications

Additional Information:

• Delivery Time: 9.00Am to 6.00 Pm

Product Details :
Features :

• Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete.
• The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand.
• The low water requirement ensures high early strength and long-term durability.
• For larger repairs, the mixed Renderoc RG may be modifi ed by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site.
• For exceptionally large repairs, the local Fosroc offi ce shall be consulted.

Advantages :

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Highly fluid to allow for placement without vibration.
• Pre-packed to overcome site-batched variations.
• Rapid strength gain to facilitate early reinstatement.
• High ultimate strengths and low permeability of cured repair.
• Contains no chloride admixture.

Buy fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG online in India at wholesale rates. If you have been looking for fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG dealers, your search ends here as you can get the best fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG distributors in top cities such as Delhi NCR, Mumbai, Chennai, Bengaluru, Kolkata, Chennai, Pune, Jaipur, Hyderabad and Ahmedabad. You can purchase fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG of the finest quality and rest assured to get the best in terms of both durability and performance. If you are bothered about the fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG prices, you can be totally sure to get the best rates as brings you genuine fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG rates and quality assured products only from the best of brands with exclusive brand discounts you wont find anywhere else. Procure fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG today and avail the best offers on your purchase.

Epoxy resin primer for Fosroc flooring and coating rangeUsesNitoprime 25 is a general purpose anti-corrosion primer for concrete and steel surfaces (prepared by abrasive blast cleaning), for use with various Fosroc coatings and flooring range. The product actively prevents corrosion and is tolerantto application over manually prepared surfaces.

Additional Information:

• Delivery Time: 9.00AM TO 6.00 PM

Being one of the renowned organizations in the industry, we are highly engaged in providing a premium quality range of Fosroc Renderoc RG.

High performance pure epoxy 3:1 resin cartridge system, for anchoring reinforcement and fixings into a variety of substrates.
Uses
For concrete (solid, porous and light) and solid masonry.
Accredited for use in dry, damp and flooded concrete substrates
Can be used with cracked concrete
Fixing of post installed reinforcement
Anchoring of threaded rod fixings
Anchoring of internal threaded rod sleeves
Internal, external and submerged conditions
Can be applied to almost any size of fixing
For horizontal, vertical and overhead application
Bonding and surface crack sealing applications Advantages
High Bond strengths
No additional mixing equipment required
C1 and C2 seismic resistance*
Does not apply expansive force to the substrate
Fixings can be spaced closer together than mechanical anchors
Enables fixings closer to edges than mechanical anchors
Resistant to a variety of chemicals
Low VOC
Tested with diamond drilled bore holes
Fire rated up to 2 hours*
Waterproof, protecting the fixing from corrosio
Material Properties
Compressive Strength (EN196) >110 MPa
Flexural Strength (EN196) >40MPa
E Modulus (EN196) 10,800 MPa
Shore D Hardness 85
Density 1.41kg/L
Temporary service temperature -40 to +72°C
Permanent service temperature -40 to +43°C
Electrical resistance (IEC93) 1.2 x1012 Ωm
Thermal Conductivity (IEC 600093) 0.47W/m.K

Additional Information:

• Production Capacity: Rebairing Chemical
• Delivery Time: 2 days